L stack of images of a total protein stain and a

L stack of images of a total protein stain and a DNA stain respectively. Since the images we analyze in this paper are only 2D slices, we developed an approach to estimate an approximate 3D shape of a cell and nucleus from a 2D slice (purely for the purpose of being able to generate a synthetic microtubule distribution). The location of the centrosome was also estimated (see Methods). Figure 3 shows an example of microtubule and nucleus images and the resulting approximate 3D cell and nucleus shape models (see details in the section of “3D cell and nuclear morphology generation” in Methods). We also describe a method to detect the 3D coordinate of the centrosome from the microtubule image using a two step approach (see Methods). These models and centrosome location were then used to generate microtubules in the cytosolic space.Recovering 3D Microtubule Generative Model Parameters from 2D Images: comparisons with real 3D estimatesTo test the accuracy of estimating microtubule parameters from 2D images, we applied our new 2D method (see Methods) using the central slice (at half Anlotinib supplier height of the cell) of 3D HeLa cell images and compared the estimated parameters with those from the 3D method. The half height was chosen as the preferred slice because the 2D images used later were also acquired at half the height of the cell. We computed the mean absolute percentage error (MAPE) in each of the parameters estimated from the 2D images assuming that the estimated parameters from the 3D method were correct. Results are shown in Table 1 for 42 cells. From the table, we can see that the estimates of the number of microtubules and collinearity from a single 2D slice are reasonably close to those from the entire 3D image. However, the MAPE for the mean length appears to be somewhat larger. We will aim to reduce this discrepancy in future work. However, we note that most cells were estimated to have mean length of 10 or 15 microns (see the section of library generation in Methods) using the 3D method on the original 3D images. Therefore a small deviation in the estimates of 5 microns (the increment of the range of allowed values of mean length) would cause a MAPE of 50 or 33. The table also shows aFigure 1. Growth model for generating microtubules dependent on cell and nuclear shapes. Each microtubule starts from 23727046 the centrosome, and randomly grows to the second point on the lateral surface of a cone whose aperture is 2a. Then the microtubule grows the same way until it hits the cell or nuclear shape boundary and is not able to step further within the cytosolic area. At this time, we relax the collinearity requirement but still confine the next direction under the local constraint alocal. Moreover, we also keep on checking a consecutive multiple (30) steps, and require that there are less than or equal to 3 pairwise vector angles that are larger than the global constraint aglobal. Beginning with an empty (black) cytosolic area (shaped by cell and nuclear boundary), we add one to the intensity of the pixel which a microtubule crosses. In this paper, we used every step of growth to be 0.2 microns (1 pixel). For the two constraints on the collinearity which controls the curvature of each microtubule and the local and global rebounding issues, we used alocal to be 63.9 degrees and aglobal to be 120 degrees. The figure only illustrates the procedure of growth in 2D for 47931-85-1 chemical information better visualization but can be easily imagined to extend to 3D.Comparison of Microtubule.L stack of images of a total protein stain and a DNA stain respectively. Since the images we analyze in this paper are only 2D slices, we developed an approach to estimate an approximate 3D shape of a cell and nucleus from a 2D slice (purely for the purpose of being able to generate a synthetic microtubule distribution). The location of the centrosome was also estimated (see Methods). Figure 3 shows an example of microtubule and nucleus images and the resulting approximate 3D cell and nucleus shape models (see details in the section of “3D cell and nuclear morphology generation” in Methods). We also describe a method to detect the 3D coordinate of the centrosome from the microtubule image using a two step approach (see Methods). These models and centrosome location were then used to generate microtubules in the cytosolic space.Recovering 3D Microtubule Generative Model Parameters from 2D Images: comparisons with real 3D estimatesTo test the accuracy of estimating microtubule parameters from 2D images, we applied our new 2D method (see Methods) using the central slice (at half height of the cell) of 3D HeLa cell images and compared the estimated parameters with those from the 3D method. The half height was chosen as the preferred slice because the 2D images used later were also acquired at half the height of the cell. We computed the mean absolute percentage error (MAPE) in each of the parameters estimated from the 2D images assuming that the estimated parameters from the 3D method were correct. Results are shown in Table 1 for 42 cells. From the table, we can see that the estimates of the number of microtubules and collinearity from a single 2D slice are reasonably close to those from the entire 3D image. However, the MAPE for the mean length appears to be somewhat larger. We will aim to reduce this discrepancy in future work. However, we note that most cells were estimated to have mean length of 10 or 15 microns (see the section of library generation in Methods) using the 3D method on the original 3D images. Therefore a small deviation in the estimates of 5 microns (the increment of the range of allowed values of mean length) would cause a MAPE of 50 or 33. The table also shows aFigure 1. Growth model for generating microtubules dependent on cell and nuclear shapes. Each microtubule starts from 23727046 the centrosome, and randomly grows to the second point on the lateral surface of a cone whose aperture is 2a. Then the microtubule grows the same way until it hits the cell or nuclear shape boundary and is not able to step further within the cytosolic area. At this time, we relax the collinearity requirement but still confine the next direction under the local constraint alocal. Moreover, we also keep on checking a consecutive multiple (30) steps, and require that there are less than or equal to 3 pairwise vector angles that are larger than the global constraint aglobal. Beginning with an empty (black) cytosolic area (shaped by cell and nuclear boundary), we add one to the intensity of the pixel which a microtubule crosses. In this paper, we used every step of growth to be 0.2 microns (1 pixel). For the two constraints on the collinearity which controls the curvature of each microtubule and the local and global rebounding issues, we used alocal to be 63.9 degrees and aglobal to be 120 degrees. The figure only illustrates the procedure of growth in 2D for better visualization but can be easily imagined to extend to 3D.Comparison of Microtubule.